A high-temperature dishwasher sanitises with hot water, with a final rinse of at least 82°C. A low-temperature dishwasher washes at much lower temperatures and sanitises with a chemical. Both can produce safe tableware. The difference lies in what your team must do every day, what the machine costs to run, and how much the kitchen depends on staff following a routine. This guide sets out the two types, compares them on practical criteria, and explains how pass-through, conveyor and glasswasher formats fit in.
TL;DR
- High-temp machines sanitise with a final rinse of at least 82°C. Low-temp machines wash and rinse at roughly 49°C to 60°C and rely on a chemical sanitiser.
- Low-temp machines need daily chemical checks with test strips, and records of those checks. High-temp machines need a temperature check instead.
- Choose the machine type by peak service volume, not average volume. A pass-through (hood-type) machine suits most restaurants. A conveyor is justified only by continuous high volume.
- A glasswasher is a smaller machine for glassware and cups. It does not replace a dishwasher for plates, trays and cookware.
- Confirm any grant eligibility with Enterprise Singapore before you buy, because categories are reviewed from time to time.
Table of Contents
- How the two machine types sanitise
- Side-by-side comparison
- The daily routine behind each type
- Running costs and energy
- Which kitchens suit which type
- Pass-through vs conveyor dishwashers
- Glasswasher vs dishwasher
- Our perspective
- Choosing a machine: a checklist
- See our dishwasher range
- FAQ
- Sources
How the two machine types sanitise
Commercial dishwashers are classified by their sanitising method. The BC Centre for Disease Control guideline on mechanical warewashing describes the split as follows:
- High-temperature machines sanitise with a final rinse of at least 82°C (180°F).
- Low-temperature machines use wash and rinse water between 49°C and 60°C (120°F to 140°F). They disinfect with a chemical sanitiser such as chlorine, iodine or a quaternary ammonium compound.
The temperature figure for high-temp machines depends on the machine design. FoodSafePal’s dishwashing guidance gives a minimum sanitising rinse of 74°C (165°F) for a stationary-rack, single-temperature machine, and 82°C (180°F) for all other machines. The same page advises that the rinse should not exceed 90°C (194°F), because water begins to vaporise at that point and the rinse becomes less effective.
These figures come from North American public health guidance. They are a useful reference for specifying equipment. For the standard your premises must meet, ask the Singapore Food Agency or your licensing contact, and ask the equipment supplier to confirm in writing the rinse temperature the machine is designed to reach.

What the hot rinse achieves
In a high-temp machine, heat does the sanitising. The wash water removes soil, and the final rinse brings the surface of the dishes to a temperature that kills pathogens. FoodSafePal notes that these rinse temperatures are intended to bring the surface of the dishes to at least 71°C (160°F), and suggests verifying this with a heat-sensitive test strip attached to a dish.

A useful side effect is drying. Dishes leave the machine hot, and moisture evaporates quickly, so the tableware can be stacked and returned to service sooner.
What the chemical does
In a low-temp machine, the sanitiser is dosed automatically into the final rinse. The machine itself does not need a booster heater to reach 82°C. The sanitising result depends on the chemical being present at the correct concentration. If the supply runs out, the dosing line blocks, or the concentration drifts, the machine can look as though it is working while sanitising poorly.
Side-by-side comparison
| Criterion | High-temp dishwasher | Low-temp dishwasher |
|---|---|---|
| Sanitising method | Hot final rinse, 82°C or above for most machines | Chemical sanitiser in the final rinse |
| Wash and rinse water | Hot, with a booster heater for the final rinse | About 49°C to 60°C |
| Daily verification | Check the rinse temperature gauge or use a heat-sensitive strip | Test the chemical concentration with test strips and keep records |
| Consumables | Detergent and rinse aid | Detergent, rinse aid and sanitiser |
| Electricity use | Higher heating load, as water must reach a high rinse temperature | Lower heating load |
| Plate temperature on exit | Hot, dries quickly | Cooler, may need longer to air-dry |
| Risk to staff | Hot surfaces and steam when doors are opened | Lower burn risk, but staff handle chemicals |
| Main failure point | Booster heater fault or low water temperature | Empty or mis-dosed sanitiser |
Two rows in this table deserve more attention than the rest.
The daily routine behind each type
The most important difference between the two is not the machine. It is the routine you must run.
The BCCDC guideline explains that low-temp machines require the operator to measure the chemical sanitiser concentration with test strips, and the practical consequence is documentation. If your kitchen follows a HACCP-based food safety plan, the readings belong in your records. The warewashing article in Food Protection Connection likewise lists the use of proper chemical test strips among the controls for chemical-sanitising machines, and notes that the wash water in such machines should not fall below 120°F (49°C).
For a low-temp machine, a sensible daily routine looks like this:
- Check that the sanitiser container is filled and the dosing line is clear.
- Run a cycle and test the rinse water with the test strip supplied for that chemical.
- Record the reading, the time and the name of the person who checked it.
- If the reading is outside the range, stop using the machine for sanitising and call the supplier.
For a high-temp machine, the routine is shorter:
- Run a cycle and read the final rinse temperature on the gauge.
- Record it if your plan requires it.
- If the reading is below the machine’s stated rinse temperature, report the fault. A failing booster heater is the usual cause.
In a kitchen with frequent staff changes, the second routine is easier to teach and harder to get wrong. In a small kitchen with a steady team and a disciplined supervisor, the first is entirely workable.
Running costs and energy
High-temp machines carry a heating cost, because the final rinse must reach a high temperature on every cycle. Low-temp machines avoid most of that but add a recurring chemical cost. Neither is cheaper in every kitchen. The result depends on your volume, your water supply temperature and the price of sanitiser from your supplier.
If energy use is the deciding factor, ask for the following figures in writing for each model you are considering:
- Electrical load of the wash tank heater and the booster heater, in kW.
- Water consumed per rack, in litres.
- Whether heat recovery or a steam condensing option is available.
- Recommended sanitiser consumption per rack for low-temp models.
On the machine format, one buying guide notes that heat recovery is available on mid-range and above machines and can reduce energy draw by 15% to 25% on conveyors, according to Hospitality Hub’s pass-through and conveyor comparison. Treat that as an indication to ask suppliers about, not a guarantee for any particular model.
Grants and dishwashers
Singapore operators often ask whether a dishwasher qualifies for an energy grant. As of April 2026, commercial dishwashers were not listed as a pre-approved equipment category under the Enterprise Singapore Energy Efficiency Grant for food services. Grant categories are reviewed periodically, so confirm the current position with Enterprise Singapore before you place an order. Do not assume that a machine is covered because it is described as energy-efficient.
For the equipment categories that have been eligible, and the current grant structure, see our guides to the EDGE grant and kitchen equipment in Singapore and the list of energy efficiency grant eligible equipment.
Which kitchens suit which type
High-temp suits
- Hotels, chains and central kitchens where several shifts use the machine and staff turnover is high. Industry observations in Singapore indicate that chains and hotels increasingly specify high-temp machines because the sanitising result does not depend on a person dosing or testing a chemical.
- Kitchens with heavy, greasy loads, where a hot wash helps to remove baked-on residue.
- Operations that need dishes dry and ready for stacking straight from the machine.
Low-temp suits
- Small cafés and bars with a stable team and light plate counts.
- Premises where a booster heater load would stress the electrical supply.
- Operations where a lower burn risk for staff matters, for example where the machine is in a narrow, shared space.
Neither list is a rule. The right test is whether your team will do the daily checks every day. If the honest answer is uncertain, a high-temp machine removes that dependency.
Pass-through vs conveyor dishwashers
Readers often ask about this choice alongside temperature. The two questions are separate. Pass-through and conveyor describe how racks move through the machine. High-temp and low-temp describe how the machine sanitises. Most formats are available in either type.
| Format | How it works | Suited to |
|---|---|---|
| Undercounter / counter | Rack loaded by hand into a small chamber beneath or on a counter | Cafés, bars, small kitchens |
| Pass-through (hood-type) | Rack is slid in, the hood is lowered, then the rack is slid out the other side | Medium to high-volume restaurants |
| Conveyor (flight-type) | Racks or items travel continuously through wash and rinse zones | Cafeterias, institutions, high-volume kitchens |
The Hospitality Hub comparison cited above advises matching the machine to peak service volume rather than average daily usage. It describes a pass-through machine as the standard for medium to high-volume restaurants, typically processing 40 to 70 racks per hour. It describes conveyor or flight-type machines as necessary only where throughput is continuously high, above roughly 150 to 200 racks per day, and warns that over-investing in a conveyor for variable volume leads to unnecessary utility costs.
A worked example shows the logic. A restaurant serves 80 covers on a normal evening and 250 at a weekend peak. Its dish room must clear the peak, but the machine idles for most of the week. A pass-through machine with a good loading table and a staff member dedicated to the dish area will cope with the peak. A conveyor would be far larger than the kitchen needs, and would also take more floor area and more utilities.
Glasswasher vs dishwasher
A glasswasher is a compact machine designed for glasses, cups and similar items. It is common in bars and cafés. A general dishwasher handles plates, cutlery, trays and often small cookware. The practical points:
- A glasswasher uses baskets and spray arms sized for glassware, so it is not designed for plates or trays.
- A dishwasher with a glass rack can wash glasses, but it is slower and may leave more residue on glass if the rinse aid is not set correctly.
- Many premises need both: a glasswasher at the bar, and a dishwasher in the kitchen.
The temperature question applies to both. Glasswashers also come in high-temp and low-temp versions, and the same daily checks apply.
Our perspective
We supply commercial kitchen equipment to Singapore restaurants, caterers and food manufacturers. When operators ask us about dishwashers, the first thing we ask is not the budget. We ask who will run the machine at 10 pm on a busy Saturday.
Our view is that a sanitising method is only as reliable as the routine around it. A low-temp machine is a sound choice when the chemical checks are assigned to a named person and recorded. Where they are not, a high-temp machine is the more dependable choice, because the heat does the work without a daily dosing decision.
We also advise operators to size the machine for the busiest hour, then stop. A larger machine than the kitchen needs adds floor space, water use and electricity cost without improving service. We apply the same thinking to energy-efficient equipment generally, which is why we publish guidance on buying energy-efficient kitchen equipment first and on cutting restaurant energy bills.
Before you commit to a dishwasher, check the electrical load, water connection, drainage and ventilation of the dish area. Steam from a hot rinse affects the dish room, so read our note on kitchen ventilation requirements in Singapore as well.
— David
Choosing a machine: a checklist
Use these questions when you compare quotations:
- Sanitising method. Is it a high-temp or low-temp model, and what final rinse temperature or chemical concentration is specified?
- Peak volume. How many racks per hour must the machine clear in your busiest service?
- Rack size and dish mix. Can the rack take your plates, trays and glassware?
- Utilities. What are the electrical phase and load, the water inlet temperature and pressure, and the drain position?
- Daily checks. What does the supplier say the operator must test or record each day?
- Servicing. Who services the booster heater or the chemical dosing pump, and how quickly?
- Certification. Does the machine meet a recognised commercial warewashing standard? The BCCDC guideline refers to NSF/ANSI standards for commercial warewashing or equivalent.
- Layout. Is there a loading table, a scraping station and a clean-dish table sized for the machine?
See our dishwasher range
We list a counter dishwasher and a dishwasher hood on our site, and our showroom lets you see equipment before you buy. Our full equipment collections cover refrigeration, cooking, warming and stainless steel fittings for the rest of the kitchen. Contact us with your peak volume and dish room dimensions and we will advise on a suitable configuration.
FAQ
What is the difference between a high-temperature and a low-temperature dishmachine?
A high-temperature machine sanitises with a final rinse of at least 82°C in most designs. A low-temperature machine washes and rinses at about 49°C to 60°C and sanitises with a chemical. The high-temp type needs a temperature check, and the low-temp type needs daily chemical test strips and records.
Is a low-temp dishwasher less hygienic?
Not when it is maintained correctly. Both types are accepted sanitising methods in the guidance cited above. The risk with low-temp machines is human: an empty sanitiser container or an unchecked concentration can leave dishes poorly sanitised. A documented daily check controls that risk.
Do I need a conveyor dishwasher for a busy restaurant?
Usually not. A pass-through machine typically handles 40 to 70 racks per hour, which suits most medium to high-volume restaurants. A conveyor is justified when throughput is continuously high, such as in a cafeteria or institution. Size the machine for your peak hour, not your average day.
Is a glasswasher the same as a dishwasher?
No. A glasswasher is a compact machine built for glasses and cups, while a dishwasher is built for plates, trays and cutlery. Bars often use both. Each is available in high-temp and low-temp versions.
Can I claim a grant for a commercial dishwasher in Singapore?
As of April 2026, commercial dishwashers were not listed as a pre-approved category under the Enterprise Singapore Energy Efficiency Grant for food services. Categories are reviewed periodically, so confirm the current position with Enterprise Singapore before you order.
Sources
- BC Centre for Disease Control: guidelines for mechanical warewashing in food service establishments
- FoodSafePal: dishwashing temperature guidelines for food safety
- Food Protection Connection: warewashing
- Hospitality Hub: pass-through vs conveyor dishwasher comparison
